How to setup stabilisers for a Forme Cubley
1
Remove the stabilisers from their packaging.
2
You can tighten the nut using the 15mm spanner, the stabilisers should be raised from the ground.
3
Now place the bracket over the end.
![Step 4](/_next/image?url=https%3A%2F%2Fwww.datocms-assets.com%2F75508%2F1703071661-4.jpg%3Fdpr%3D0.25%20200w%2Chttps%3A%2F%2Fwww.datocms-assets.com%2F75508%2F1703071661-4.jpg%3Fdpr%3D0.5%20400w%2Chttps%3A%2F%2Fwww.datocms-assets.com%2F75508%2F1703071661-4.jpg%3Fdpr%3D0.75%20600w%2Chttps%3A%2F%2Fwww.datocms-assets.com%2F75508%2F1703071661-4.jpg%20800w&w=3840&q=75&dpl=dpl_fDdqouLfgRk3sCJ73EoQhZmq1PzB)
4
Ensure that the bracket fits on the frame as above.
![Step 5](/_next/image?url=https%3A%2F%2Fwww.datocms-assets.com%2F75508%2F1703071715-5.jpg%3Fdpr%3D0.25%20200w%2Chttps%3A%2F%2Fwww.datocms-assets.com%2F75508%2F1703071715-5.jpg%3Fdpr%3D0.5%20400w%2Chttps%3A%2F%2Fwww.datocms-assets.com%2F75508%2F1703071715-5.jpg%3Fdpr%3D0.75%20600w%2Chttps%3A%2F%2Fwww.datocms-assets.com%2F75508%2F1703071715-5.jpg%20800w&w=3840&q=75&dpl=dpl_fDdqouLfgRk3sCJ73EoQhZmq1PzB)
5
This is how it will look from the other side.
6
Place the stabiliser over the bracket.
7
Slide on the washer.
8
Screw the wheel nut onto the end.
9
You can tighten the nut using the 15mm spanner, the stabilisers should be raised from the ground.
![Step 10](/_next/image?url=https%3A%2F%2Fwww.datocms-assets.com%2F75508%2F1703072110-10.jpg%3Fdpr%3D0.25%20200w%2Chttps%3A%2F%2Fwww.datocms-assets.com%2F75508%2F1703072110-10.jpg%3Fdpr%3D0.5%20400w%2Chttps%3A%2F%2Fwww.datocms-assets.com%2F75508%2F1703072110-10.jpg%3Fdpr%3D0.75%20600w%2Chttps%3A%2F%2Fwww.datocms-assets.com%2F75508%2F1703072110-10.jpg%20800w&w=3840&q=75&dpl=dpl_fDdqouLfgRk3sCJ73EoQhZmq1PzB)
10
Repeat the same steps for the opposite side.
11
Lastly, ensure that the bike is able to rock slightly.